Velleman HAA2801 Bedienungsanleitung

HAA2801Programming & Installation ManualFOR ELECTRIC LOCK, INTER-LOCKAND SECURITY SYSTEM INSTALLATIONSSPLIT-DECODED CONTROLLERFOR HAA28XX SERIES S

10CONNECTION TERMINALS

1 - 2 : 12-24V DC I/P -- (Power Input Terminal)Connect to a 12-24V DC power supply. The (-) supply and the (-) GND are the common grounding points of

1210 : DOOR SENS N.C. -- (Door Position Sensing Input -- Normally Close)A Normally Closed (N.C.) sensing point referring to (-) ground, with the help

1319 - 20 - 21 : OUTPUT 3 -- (Output Relay 3)1 Amp relay dry contact controlled by the Group 3 User PINs & Cards in Split-decoded mode or by the R

14THE AUDIBLE AND VISIBLE SIGNALS

15RF REMOTE CONTROLLER -- (HAA2800 ONLY)

16APPLICATION EXAMPLES1) BASIC WIRINGS OF A SPLIT-DECODED DOOR LOCKNOTE: • Connect the 1N4004 as close as possible to the lock in parallel with the l

172) BASIC WIRINGS OF AN INTER-LOCK SYSTEM USING TWO SPLIT-DECODED KEYPADS An inter-lock system needs two door controllers. This application example u

APPLICATION HINTS FOR THE AUXILIARY TERMINALSThe tamper switch is Normally Closed while the keypad is secured on the gang box. It is open when the key

The Duress Output switches to (-) ground when duress code is entered. You may use it to turn ON an LED lamp and/ or a small buzzer to notify a guard;

TABLE OF CONTENTSINTRODUCTIONFEATURESSPECIFICATIONSPACKAGE CONTENTSTHE SPLIT-DECODED CONTROLLER UNIT (Figure 1)THE MAIN CIRCUIT BOARD OF THE CONTROLLE

20Use the Normally Open (N.O.) output contact to shunt a Normally Closed (N.C.) protection zone of an alarm system.Set output contact to Start / Stop

PROGRAMMING FOR FULL FEATURES --- (Supplementary Information)In the Split-decoded operation mode, the keypad becomes a data entry tool of the system a

DIRECT ACCESS TO PROGRAMMING MODE WITH THE “DAP” CODE – 8 0 8 0

REFRESH THE SYSTEM WITH THE “REFRESHING CODE” --- 9 9 9 9

FEATURE PROGRAMMING -- KEY IN AND STORE THE DESIRED VALUES

Example: User Name Location Function Code User ID PIN/Code Card # Remark12345678910111213141516--1,000RECORD A MASTER CODE --For Both Master & Sla

OPERATION AND FUNCTIONS OF THE SUPER USER PIN

03 #RECORD-DELETE PINS OR CARDS FOR OUTPUT 1, 2, & 3 (Locations 10, 20 & 30)

EXAMPLES – PROGRAMMING AND OPERATION

4) Example 4 -- EM Card + Common User PIN :i) Programming :10 4 003 # (a) (b) (c) (d) (e)(a) (b) (c

3User PIN Entry ModePacier Tones On-Off SelectionOutput Operation AnnouncerStatus LED Flashing On-Off during StandbyDoor Forced Open Warning & Ti

Operation : (while the system is in the operation mode) # (a) (b) (c)(a) (b) (c)NOTE: The Duress Event can not be

Example 3: Delete a “Visitor Code” from Vistor ID 02 in the memory 40 02 # (a) (b) (c)(a) Visitor Code Programming, (b) The Visito

Example 2: Set a “Duress Code” with the number of “2 3 9 8 0” for Output 242 01 23980 # (a) (b) (c)

CONFIGURATION OF THE OUTPUT MODES OF OUTPUT 1, 2 AND 3 (Locations 51, 52 & 53)

USER PIN ENTRY MODE – Auto or Manual (Location 70)

STATUS LED FLASHING ON-OFF DURING STANDBY (Location 73)

INTELLIGENT EGRESS BUTTON – AN UNIQUE FEATURE OF A CONTEMPORARY KEYPAD

EGRESS DELAY , WARNING AND ALARM (Location 90)

EXAMPLES:Example 1: Set Egress Button in Momentary contact 5 seconds with delay & warning beep90 2 5 # (a) (b)

CLOSE THE PROGRAMMING MODE ( * * )

INTRODUCTION

40THE PROGRAMMING SUMMARY CHART --- (Supplementary Information)LOCATIONFUNCTIONENTRY LIMITS & CODE OPTIONSCODE ENTRYFACTORY DEFAULT0 1Master Code

418 0Door Forced Open Warning & TimeFUNCTION MODE / TIME:0---OFF1-999 Seconds80 FUNCTION / TIME #Mode = 0, Door Forced OpenWarning OFF8 1Propped-u

EnglishVelleman® Service and Quality WarrantySince its foundation in 1972, Velleman® acquired extensive experience in the electronics world and curren

SPECIFICATIONS

THE SPLIT-DECODED CONTROLLER UNIT (Figure 1)THE MAIN CIRCUIT BOARD OF THE CONTROLLER --- (Figure 2) NOTE: Factory suggest that the work of timer adju

INSTALLATION

THE NECESSARY CONNECTIONS FOR SPLIT-DECODED

9Example – Change of the Link-up Code ( The Master Code of the Master Keypad)a) Put the Link-up Jumper of the Decoder from OFF to ONOFF ONb)