Velleman KNS6 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Spielzeuge Velleman KNS6 herunter. Velleman KNS6 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 8
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
KNS6 VELLEMAN 1
KNS6 – TRAINMECH
1. Introduction & Characteristics
Thank you for buying the KNS6 ! Read this manual carefully before bringing the KNS6 into use.
Familiarise yourself with the operation of transmissions steered through gears or pulleys.
Easy to build, no glue or soldering required.
Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS6 – Figures”!!!
2. Parts List
Part Quant. Description Part Quant. Description
1 1 gearbox 17 2 pulley (15 x 1.9mm)
2 1 battery holder 18 2 nylon post (H = 6mm)
3 1 motor DC 6V 19 8 nylon post (H = 3mm)
4 1 slide switch with wire 20 3 PVC tube (15 x 1.5mm)
5 1 metal shaft (2 x 40mm) 21 8 nut M3
6 1 metal shaft (3 x 52mm) 22 4 screw (3 x 12mm)
7 5 metal shaft (2 x 60mm) 23 2 screw (3 x 16mm)
8 1 pinion gear 10T (white) 24 2 screw (3 x 20mm)
9 1 face gear (36T/14T) 25 8 washer (3.2 x 10 x 0.5mm)
10 1 gear 36T/0T 26 32 self-tapping screw (2 x 4mm)
11 1 gear (36T/14T) 27 2 self-tapping screw (2 x 6mm)
12 1 gear (36T/14T) 28 10 nylon pad (5.6 x 4.8 x 1.95mm)
13 1 wire with terminal (yellow) 29 10 nylon pad (Ø8mm)
14 1 wire with terminal (green) 30 10 nylon pad (6.6 x 4.8 x 2.1mm)
15 2 belt (40 x 1.2mm) 31 8 nylon connector (N-shaped)
16 2 pulley (15 x 2.9mm) 32 13 fixing plate (L-shaped)
3. Prepunched Boards (see KNS6 – Figures
)
4. Assembly (see also KNS6 – Figures
)
Fig. 3 : The gears (n°9/10/11/12) should be placed to the left of the pinion gear (n°8). Note that the protruding
edge should point towards the metal case.
Fig. 4 : Screw 1 x piece n°32 on boards 1 & 2 and attach them to boards n°3 & 4.
Seitenansicht 0
1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare